When I started soldering everything was big and had leads that went through holes in the board. You inserted the leads, bent them over to hold the component, flipped the board over, soldered everything, and trimmed off the excess leads.

Now I’m soldering things down to 0402 SMDs (1/4 the size of the smallest component in the picture) using a needle point soldering tip and a microscope.

A pair of 2N2222 transistors, one SOT23 and one TO-92.

  • ______
    link
    fedilink
    arrow-up
    8
    arrow-down
    16
    ·
    1 year ago

    None of these components are hard to solder. Also there are other soldering methods, you don’t need to hand solder these.

    But yes. It is harder than before.

    • MapleEngineer@lemmy.caOPM
      link
      fedilink
      English
      arrow-up
      16
      arrow-down
      1
      ·
      1 year ago

      It is harder for a beginner with a $10 soldering iron from the local hardware store than it was when I started 45 years ago. Most people don’t start with hot plates or reflow ovens or hot air.

      • VanillaGorilla@kbin.social
        link
        fedilink
        arrow-up
        3
        ·
        1 year ago

        True. I mean you can still find most parts that you used 45 years ago, but making it small and using modern parts might require some new tools. You can get a tiny hot plate on Ali for cheap, but I’m not sure how good it is. There are people utilizing cheap irons as well.

        • MapleEngineer@lemmy.caOPM
          link
          fedilink
          English
          arrow-up
          2
          ·
          1 year ago

          I’ve seen the tiny ones. I think I’m more likely to build a small reflux oven. I only ever build one or two of anything unless I take in a job for someone else.

        • Saturdaycat@kbin.social
          link
          fedilink
          arrow-up
          2
          ·
          1 year ago

          Are there good instructions out there for people using cheap irons to solder these small components? How does one get into soldering now with a hot plate vs hand iron considering that these components have a much higher learning curve than the older larger parts ?

          • ______
            link
            fedilink
            arrow-up
            2
            ·
            1 year ago

            The cheap soldering irons are tricky because heat distribution is crucial. If your iron is not at the right temperature and the heat transfer is not uniform you can fry a component instantly, specially the smaller components. you need a soldering iron with temperature dials at bare minimum

          • Chreutz@lemmy.world
            link
            fedilink
            arrow-up
            2
            ·
            1 year ago

            If you want to do really low investment hot plate soldering, some solder paste, good tweezers and a frying pan with some sand in it is probably good. Just keep an eye on it while heating, and stop when the solder melts

          • MapleEngineer@lemmy.caOPM
            link
            fedilink
            English
            arrow-up
            2
            ·
            edit-2
            1 year ago

            I’m working on making some videos to show what can be done with basic equipment even with modern, small components. Maybe I should add some soldering 101 type videos? I can add them to my YouTube channel for my 6 subscribers. Heh.

            EDIT: 9! 9 subscribers! Pretty soon I’ll be able to quit my day job and live off my YouTube channel.

      • ______
        link
        fedilink
        arrow-up
        2
        arrow-down
        4
        ·
        1 year ago

        You’re saying that as if most beginners start with smt. Nowadays if you want to build your circuit you can have it made with the PCB already soldered at very affordable prices.

        • MapleEngineer@lemmy.caOPM
          link
          fedilink
          English
          arrow-up
          1
          ·
          edit-2
          1 year ago

          What I’m saying is that it’s possible for beginners with basic equipment to begin to work with SMDs. Sure, you can order THT components and build all THT boards but the people that I talk to want to use modern components and modern techniques so that they boards don’t look quite so…1970s.

          SMDs have made things more challenging but with basic equipment and knowledge it is doable.