I have a few selfhosted services, but I’m slowly adding more. Currently, they’re all in subdomains like linkding.sekoia.example etc. However, that adds DNS records to fetch and means more setup. Is there some reason I shouldn’t put all my services under a single subdomain with paths (using a reverse proxy), like selfhosted.sekoia.example/linkding?

  • TemperateFox@beehaw.org
    link
    fedilink
    arrow-up
    4
    arrow-down
    5
    ·
    edit-2
    1 year ago

    Everyone is saying subdomains so I’ll try to give a reason for paths. Using subdomains makes local access a bit harder. With paths you can use httpS://192etc/example, but if you use subdomains, how do you connect internally with https? Https://example.192etc won’t work as you can’t mix an ip address with domain resolution. You’ll have to use http://192etc:port. So no httpS for internal access. I got around this by hosting adguard as a local DNS and added an override so that my domain resolved to the local IP. But this won’t work if you’re connected to a VPN as it’ll capture your DNS requests, if you use paths you could exclude the IP from the VPN.

    Edit: not sure what you mean by “more setup”, you should be using a reverse proxy either way.

    • tkohhh@waveform.social
      link
      fedilink
      arrow-up
      3
      ·
      1 year ago

      If your router has NAT reflection, then the problem you describe is non existent. I use the same domain/protocol both inside and outside my network.

        • tkohhh@waveform.social
          link
          fedilink
          arrow-up
          1
          ·
          1 year ago

          I don’t know for sure… but my instinct is that NAT reflection is moot in that case, because your connection is going out past the edge router and doing the DNS query there, which will then direct you back to your public IP. I’m sure there’s somebody around that knows the answer for certain!

        • BombOmOm@lemmy.world
          link
          fedilink
          arrow-up
          2
          arrow-down
          4
          ·
          1 year ago

          Depends:

          • If you have your VPN setup so it sends all traffic to the internet, then your request will pass through the VPN server, then back to your location from the internet.

          • If you have your VPN setup to exempt LAN traffic, then if you specify a local IP, your traffic will stay on your LAN, however, if you specify the domain, the VPN will almost certainly continue to treat it as internet-bound traffic and route it through their servers. This is possibly avoidable if you also put your own IP on the exempt list, if that is a feature.

    • Felix@lemmy.one
      link
      fedilink
      arrow-up
      3
      arrow-down
      1
      ·
      1 year ago

      You’ll have to use http://192etc:port. So no httpS for internal access

      This is not really correct. When you use http this implies that you want to connect to port 80 without encryption, while using https implies that you want to use an ssl connection to port 443.

      You can still use https on a different port, Proxmox by default exposes itself on https://proxmox-ip:8006 for example.

      Its still better to use (sub)domains as then you don’t have to remember strings of numbers.

      • TemperateFox@beehaw.org
        link
        fedilink
        arrow-up
        1
        arrow-down
        1
        ·
        edit-2
        1 year ago

        I understand, though if the services you’re hosting are all http by themselves, and https due to a reverse proxy, if you attempt to connect to the reverse proxy it’ll only serve the root service. I’m not aware of a method of getting to subdomains from the reverse proxy if you try to reach it locally via ip.

        • macgregor@lemmy.world
          link
          fedilink
          arrow-up
          4
          ·
          1 year ago

          Generally a hostname based reverse proxy routes requests based on the host header, which some tools let you set. For example, curl:

          curl -H 'Host: my.local.service.com' http://192.168.1.100
          

          here 192.168.1.100 is the LAN IP address of your reverse proxy and my.local.service.com is the service behind the proxy you are trying to reach. This can be helpful for tracking down network routing problems.

          If TLS (https) is in the mix and you care about it being fully secure even locally it can get a little tricky depending on whether the route is pass through (application handles certs) or terminate and reencrypt (reverse proxy handles certs). Most commonly you’ll run into problems with the client not trusting the server because the “hostname” (the LAN IP address when accessing directly) doesn’t match what the certificate says (the DNS name). Lots of ways around that as well, for example adding the service’s LAN IP address to the cert’s subject alternate names (SAN) which feels wrong but it works.

          Personally I just run a little DNS server so I can resolve the various services to their LAN IP addresses and TLS still works properly. You can use your /etc/hosts file for a quick and dirty “DNS server” for your dev machine.

          • Goldenderp@lemmy.world
            link
            fedilink
            arrow-up
            1
            ·
            1 year ago

            TLS SNI will take care of that issue just fine, most reverse proxies will just handle it for you especially if you use certbot i.e. usually letsencrypt

    • Sekoia@lemmy.blahaj.zoneOP
      link
      fedilink
      arrow-up
      2
      ·
      1 year ago

      Edit: not sure what you mean by “more setup”, you should be using a reverse proxy either way.

      I’m using cloudflare tunnels (because I don’t have a static IP and I’m behind a NAS, so I would need to port forward and stuff, which is annoying). For me specifically, that means I have to do a bit of admin on the cloudflare dashboard for every subdomain, whereas with paths I can just config the reverse proxy.

      • bratling@sh.itjust.works
        link
        fedilink
        arrow-up
        1
        ·
        1 year ago

        because I don’t have a static IP and I’m behind a NAS, so I would need to port forward and stuff, which is annoying

        This week I discovered that Porkbun DNS has a nice little API that makes it easy to update your DNS programmatically. I set up Quentin’s DDNS Updater https://github.com/qdm12/ddns-updater

        Setup is a little fiddly, as you have to write some JSON by hand, but once you’ve done that, it’s done and done. (Potential upside: You could use another tool to manage or integrate by just emitting a JSON file.) This effectively gets me dynamic DNS updates.

    • key@lemmy.keychat.org
      link
      fedilink
      arrow-up
      1
      ·
      1 year ago

      I got around this by hosting adguard as a local DNS and added an override so that my domain resolved to the local IP. But this won’t work if you’re connected to a VPN as it’ll capture your DNS requests

      Why didn’t you use your hosts file?